LED Manufacturer, LED Lighting logo     English        中文
 
       
 
  All Categories
   
     
 
Product Search  
:
Param:
Keyword:
    leds,led to,led lcd,lcd led,lights,led light,led lighting,led lights,led display,led lamp,led strip,led smd,led strips,led mr16's search
  Product Model Search
 
 
  About LED
   
 

HOW TO USE LED

·FORMING:

Please do not form the LED after soldering .If forming id necessary ,it must be done before soldering .
Any unsuitable stress applied to the epoxy may break bonding wires in LED.
·SOLDERING:

Soldering Bath ---260℃±5 ℃ within 5 seconds: Soldering Iron-Under 30W within 5 seconds.(1.6mm from epoxy body)
Do not apply any force of mechanical stress onto the leads or epoxy body during soldering heat is remained.
If soldering one line of LED on a P.C . board by using a soldering iron ,don t solder both the leads of the LED at same time .
·CLEANING:

Use Alcohol ,Freon TE or Chlorosen to clean LED at normal temperature for less than l minute .
Do not use unspecified chemical liquid because it may cause crack or haze on the epoxy body.
·PREVENTING OVER CURRENT :

In order to operate LED in stable condition , please put protective resistors in series.
Resistor value can be determined by the formula
R= WHERE:
Vs=Source Voltage
VF=Forward Voltage
If=Recommended Current of LED (10-20mA)
·BRIGHTNESS:

For the purpose of obtaining uniform brightness, LED shall be same current.
It is useful for uniform brightness if you use larger source voltage and protective resistor .
QUALITY CONTROL AND ASSURANCE

·SAMPLING PLAN

U.S. Ministry of defense MIL-STD-105D level II(single sampling plans)

·INSPECTION ITEMS AND CRITERIONS FOR JUDGEMENTS

Measuring Methods for light Emitting Diodes (No.11830) and Light Emitting Diodes (No.11829) Stipulated by ministry of economical affairs of R.O.C.and by reference to Q.C. standards prevailing in prominent LED plants worldwide .

·RELIABILITY S

General provisions for Environmental s of CNS-Categorized electronic Parts ,3623-3634,5637,11233~11238,and U.S. ministry of National Defense MIL-STD-750 Specifications .

 

CONDITIONS

THERMAL SHOCK

LED placed in a chamber(-35 ℃ ) for 20 minutes , temperature increased instantaneously to +85 ℃ for 20 minutes .The duration of the shall be for 10 complete cycles .(MIL-STD-202:107D)

HUMIDIY

LED placed in humidity chamber which is maintained at 65 ℃ ,RH95 ℃ The duration of the is for 96 hours .(MIL-STD-202:103D)

LIFE

LED connected to a source of power and charged with 20mA at room temperature (25 ℃ ) for 1000 hours. MIL-STD-750:1026)

SOLDERABILITL

The pins of LED(1.6mm from body )dipped into tin which is maintained at 260 ℃± 5 ℃ . The duration of the is for 5 seconds. (MIL-std-202:208D)

VIBRATION

LED paced on a vibrator which is maintained at 10-55 Hz/minute .0.82mm amplitude.

PACKING

LED packed in a corrugated fiberboard box and fallen freely on 6faces on 6 freely at a diagonal angle to the ground. The altitude of the fall be in the range of 229-609mm considering of the range of 229-609mm considering of the packed product.

THE MEA SURING TERMS AFTER AND FAILURE CRITERIA AS FOLLOWS:

MEASURE TERMS FAILURE CRITERIA

LUMINOUS INTENSITY(I V )

LOWER STAND ARD LIMIT X 0.5

FORWARD VOLTAGE(V F )

UPPER STAND ARD LIMIT X 1.2

REVERSE CURRENT(I R )

UPPER STAND ARD LIMIT X 2.0

 

 
         
 
© 2016 LuckyLight.
Luckylight Group | Moorol Technologies | LEDs Manufacture